Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Hillsboro Homeowners
A gate that won’t open, opens halfway, or grinds to a stop leaves a driveway exposed and a routine morning stuck in park. We specialize in gate repair in Hillsboro and service automated systems across nine major brands, so the diagnosis matches the equipment instead of guessing at it. Our technicians have up to 8 years of experience with operators, control boards, loop detectors and the mechanical parts that wear first, and we carry a strong local reputation with both homeowners and property managers. If the gate is down today, call (855) 251-3899. We answer 24/7, we run fast dispatch from 7am to 7pm, and we offer same-day repair on most calls. When the work begins, the price has already been quoted, agreed and set in a written estimate, so the invoice matches the number you approved.
Driveway Gate Repair
Driveway Gate Repair covers everything between a gate that hangs wrong and one that refuses to cycle: sagging hinges, dropped posts, worn rollers, dragging tracks and operators that trip out mid-travel. You need it when the gate scrapes the ground, runs unevenly, opens partway and reverses, or when the operator runs but nothing moves. We diagnose the mechanical and the automated side together, because a loose hinge and a stalling operator look the same from the driver’s seat. Whether your system is a LiftMaster or a Mighty Mule, we test the whole path before quoting. Typical driveway gate repair in Hillsboro runs $150 to $650 depending on parts and how much of the frame and hardware has moved, and the written estimate sets the final price before we start. Automatic and operator work is scheduled rather than same-day, so you get a free measure and a clear written price.
Hinge and Post Realignment
Frost in the Willamette Valley pushes posts and pops hinge plates out of true, and a gate that was square in summer drags by January. We reset the post line and rehang the leaf so the swing clears the ground again. That single correction often cures a gate that seemed to need a whole new frame.
Operator and Safety Check
When the operator is the fault, we test travel limits, the safety reversal and the control board rather than swapping parts and hoping. If the gate stops or reverses on its own, the safety devices need attention before anyone uses it. We confirm the gate stops and reverses the way it should before we leave.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Gate Welding
Gate Welding repairs cracked joints, snapped pickets, broken hinge welds and bent frame sections on metal gates that are otherwise sound. You need it when the structural weld fails, a hinge tears loose from the post, or a strike from a vehicle leaves a kink and a hairline crack. We clean the break to bare metal, weld it properly, and treat the joint afterward so the repair holds through wet winters. Whether it’s a FAAC-hung driveway gate or a heavier commercial swing, the weld has to carry load, not just look fixed. Pricing is per job after we inspect the joint: a single weld repair typically runs $200 to $400, while a gate that needs several joints rebuilt and refinished falls in the $400 to $900 range. Welding work is scheduled, and the price is quoted and agreed before any torch is lit.
Structural Joints and Hinges
Hinge welds take the full weight of the leaf every time it swings, which is why they fail first. We rebuild the joint so the hinge sits true again rather than patching over a stress crack. Load-bearing welds get the most attention because they handle the most stress.
Straightening and Refinishing
A bent rail can be straightened, but only if the metal hasn’t gone brittle at the break. We assess the frame honestly and tell you when straightening will hold and when a section replacement is the better call. Either way, we finish the repair so it doesn’t rust through the next wet season.
Commercial Gate Repair
Commercial Gate Repair keeps entry and exit lanes moving for apartments, storage facilities, HOA entrances and business lots, where a dead gate means a backed-up line and a log of complaints. You need it when the operator faults out under heavy cycle counts, loop detectors stop sensing vehicles, or an access-control system stops recognizing credentials. We work on commercial-grade equipment such as FAAC, BFT and DoorKing operators, so we know where high-traffic systems wear and why they fault at peak hours. A typical commercial gate repair in Hillsboro runs $250 to $800 depending on the operator and controls involved, and multi-lane or access-control work is priced higher after inspection. The written estimate comes first and the price is agreed before work starts. Call (855) 251-3899 to get a lane assessed. We answer 24/7, fast dispatch from 7am to 7pm, and for measured operator work we schedule a free site visit and a written price.
Loop Detectors and Access Control
Loop detectors that miss a vehicle or trigger on nothing are a controls problem, not a gate problem. We test the loops and the controller together so the lane stops phantom-cycling. If the gate ties into a card reader or keypad, we trace that link too.
High-Cycle Operator Wear
An operator that cycles hundreds of times a day wears its gears and limits far faster than a home system. We match the diagnosis to that duty cycle and flag parts that are near the end of their service life before they strand a lane. Planned work beats an emergency that closes the entrance.
Iron Gate Repair
Iron Gate Repair handles the failures that come with a heavy, rigid gate: cracked castings, hinges that pull out of the masonry, rust that hollows a post from the inside, and latches that no longer line up. You need it when the leaf no longer swings true, rust has eaten through a joint, or a hinge has torn loose from the pillar. We look at the whole gate, then the mounting, because iron is unforgiving and a small misalignment translates to a hard bind at the hinge. Whether it’s a BFT-driven entry gate or a manual garden gate, we repair the structure and the hardware without overbuilding it. Iron gate repair in Hillsboro typically runs $200 to $700 depending on the extent of rust and whether masonry anchors need resetting. Scheduled work gets a free measure and a written price, and the estimate is agreed before we begin.
Rust and Corrosion Repair
Oregon’s wet season works on bare iron year after year, and rust often starts where a weld or a bolt traps water. We grind back to sound metal, fill and rebuild, then prime and finish so the repair doesn’t become next year’s problem. Catching rust early keeps a repair small.
Hinge and Anchor Resetting
An iron leaf is heavy, and heavy leaves pull hinges and masonry anchors out over time. We reset the anchor, rehang the leaf and confirm the swing before finishing. Getting the geometry right stops the gate from tearing itself loose again.
Sliding Gate Repair
Sliding Gate Repair fixes gates that jump the track, drag on the ground, roll rough or stop tracking straight, which are the most common failures on a slider. You need it when the gate comes off its guide, the rollers grind or seize, the track has shifted, or the operator strains to move a gate that used to glide. A slider that comes off the track is also a safety issue, because a heavy panel can tip or crush if it derails under power. We check the track, the rollers, the guide posts and the operator together, since a roller failure usually puts stress on something else. Whether the operator is a FAAC or a LiftMaster, we test the whole run before quoting. Sliding gate repair in Hillsboro usually runs $150 to $600 depending on track and roller work. Track and roller replacement and operator jobs are measured and scheduled, with a free measure and a written price first.
Track and Roller Service
A worn roller or a track that has shifted out of line makes the whole gate labor. We level the track, replace seized rollers and confirm the gate rolls free by hand before the operator goes back to work. A gate that rolls easily lasts longer.
Derailment and Guide Repair
When a slider jumps the track, the cause is usually a bent guide, a worn roller or a post that has settled. We correct the guide and the alignment so the gate stays put under power. Keeping a heavy panel on its track is a safety fix, not just a convenience one.
Wrought Iron Gate Repair
Wrought Iron Gate Repair covers the decorative and forged ironwork where appearance matters as much as function: ornamental scrollwork, spear tops, finials and the fine joints that give a gate its character. You need it when a decorative element is bent or missing, a weld on an ornate section has cracked, or rust has dulled a finish that should look sharp at the curb. We repair the ironwork and restore the finish so the gate looks right and stays structurally sound, rather than hiding damage under paint. We treat these gates as both a mechanical repair and a cosmetic one, because a gorgeous gate that binds is still a daily problem. Wrought iron gate repair in Hillsboro generally runs $200 to $650 depending on how much decorative work is involved. We schedule the work and quote it in a written estimate you approve before we start.
Ornamental Joint Repair
Scrollwork and finials take impact and lose small welds over time. We match the repair to the original pattern so the fix doesn’t stand out. Small ornamental welds are still load paths when the piece is structural.
Finish Restoration
A wrought iron gate lives or dies by its finish, and a tired coat lets rust into the joints. We prep the surface and reapply a durable finish that suits the piece. A proper finish protects the metal and keeps the gate looking like it belongs at the entrance.
Metal Gate Repair
Metal Gate Repair handles steel, aluminum and mixed-metal gates: bent frames, failed welds, worn pivots, dragging latches and hardware that has rusted solid. You need it when the gate binds, the frame is out of square, or hardware no longer lines up and the gate won’t latch or swing freely. Aluminum needs different treatment from steel, and we match the method to the metal so a repair doesn’t create a new weak point. Whether your system is a Ghost Controls operator or a heavier commercial unit, we fix the gate and confirm the operator still cycles it correctly. Metal gate repair in Hillsboro typically runs $150 to $600 depending on the metal and the extent of frame work. It’s scheduled work with a free measure and a written price, and the quote sets the final cost before anyone starts.
Frame Straightening and Alignment
A metal frame that has taken a hit often looks worse than it is, but it can also hide a stress crack. We check the frame for true and for cracks before straightening. Getting it square again stops the hardware from fighting itself.
Hardware Replacement
Latches, pivots, stops and hinges are the small parts that decide whether a metal gate feels solid. We replace worn hardware with parts suited to the gate’s weight and metal. Rusted hardware that won’t move is usually the first sign the gate needs attention.
Wood Gate Repair
Wood Gate Repair addresses the failures wood sees in a wet climate: sagging from moisture, split boards, rot at the rail and post, and hinges that pull loose as the wood softens. You need it when boards have swelled and stopped closing, a picket or rail has split, or the gate has begun to drag because a hinge pulled out. We repair the board, the joint and the hardware together so the fix lasts a season, not a week. Whether the gate hangs from a metal frame or a wood post, we check the structure underneath before deciding what needs replacing. Wood gate repair in Hillsboro usually runs $150 to $500 depending on rot and how much framing needs work. It’s measured and scheduled, and a written estimate sets the price, agreed before any work starts.
Rot and Board Repair
Wood rots from the bottom up and from the inside out at a joint, so catching it early saves the gate. We cut out soft wood and sister in sound material that takes a finish. Left alone, rot travels into the frame and turns a small fix into a rebuild.
Hinge and Sag Correction
A sagging wood gate usually means the hinge fasteners have lost their grip in soft wood. We reinforce the hinge point and rehang the gate so it swings clear. That’s the fix that stops the gate from dragging and tearing itself apart.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
We service LiftMaster operators and know where the limits and control boards tend to fault on a residential driveway. We service FAAC and BFT commercial-grade systems and understand how their duty cycles and controls wear under daily traffic. We also work on Mighty Mule residential units and Ghost Controls operators, so a homeowner system gets the same brand-specific attention as a commercial one.
Our fluency across these systems is why a diagnosis holds the first time – we recognize a brand’s known failure points instead of swapping parts to see what sticks. Gates are all we do, and that focus is the difference between a gate specialist and a generalist who occasionally touches one. Whether you have a LiftMaster, a FAAC, or any other make, we can help.
Signs You Need a Pro Right Now
- The gate stops or reverses mid-travel. That usually signals a limit, control board or safety-device fault, and it can leave the leaf in the path of a vehicle. Stop using it until it’s checked, because a partially moving gate is unsafe.
- A sliding gate comes off the track. A heavy panel that jumps its track can tip or crush, and it will only get worse under power. Do not force it back on; call and we’ll secure it.
- The operator runs but the gate doesn’t move. This points to a stripped gear, a sheared pin or a disconnected drive. Left running, the motor can overheat and turn a small fix into a full operator replacement.
- You notice sparks, burning smells or exposed wiring at the operator. Electrical problems at the operator or power supply are dangerous and belong to a trained professional. Keep people clear and call before anything is touched.
- The gate has begun to sag, scrape or bind. Early binding is cheap to correct and gets expensive fast once it stresses hinges, posts and the operator. Catch it in the first week and it stays a small repair.
Our Process, Step by Step
- 1
Call and tell us the symptom. We answer 24/7, so tell us the brand and how the gate fails: no movement, a mid-travel stop, a derail, or a noise. That first detail tells us whether the power, controls or the structure are the likely cause. Fast dispatch from 7am to 7pm gets a technician out for most calls.
- 2
Full diagnostic on arrival. We test the operator, the control board and the safety devices – limits, reversal, loop detectors where present – and check the mechanical side: hinges, tracks, rollers and posts. We don’t guess with parts; we read the system first.
- 3
Written estimate before work. You get a clear written price for what the fix actually needs, and nothing starts until you approve it. That means no invoice bigger than the quote, and no surprises after the gate is fixed.
- 4
Repair and test under load. We complete the repair and then cycle the gate repeatedly to confirm the safety reversal and the travel limits are correct. A gate is only really fixed when it works under power, not just by hand.
- 5
Walk-through and finish. We show you what failed, what we fixed and what to watch for, so you know the early signs next time. If a part is on order, the job is scheduled and the price is held to the estimate.
How Much Does Gate Repair Cost in Hillsboro?
Gate repair in Hillsboro typically runs from about $150 to $800, and the common numbers break down by the type of job. A typical driveway gate repair runs $150-$650 depending on parts and alignment work. Sliding gate repair runs $150-$600, metal gate repair $150-$600, and wood gate repair $150-$500. Heavier work costs more: wrought iron gate repair lands in the $200-$650 range, iron gate repair at $200-$700, and commercial gate repair at $250-$800 when operators and access controls are involved. Call (855) 251-3899 for an exact quote on your gate; estimates are free.
What moves the price is the failure itself, the parts, and how much of the structure has been affected. A cracked weld, a bent guide or a worn roller is different money from a control board, a loop detector or a full operator. The way to avoid overpaying is to get a real diagnosis before parts go on, which is why we test the operator and the mechanics together rather than replacing the first suspect part and waiting to see if it works.
Our free estimate includes the on-site diagnostic, a clear explanation of the likely cause, and a written price for the parts and labor the fix needs. The estimate is free, the price is set per job, and you approve it before any work starts. If we find a second problem mid-repair, you get the new price to agree before we continue.
Our Service Area Near Hillsboro
We cover Hillsboro and the surrounding towns, including Aloha, Cornelius, Forest Grove, Sherwood, Newberg, Wilsonville, Canby, St. Helens and Portland. Drive times from our dispatch vary by distance, but fast dispatch from 7am to 7pm means most Hillsboro and Aloha calls land the same day. Neighbors often reach us for gate repair just east of us, and gate repair to the west, while customers within Hillsboro find us through the main gate repair page. If you’re nearby and your gate is down, call and we’ll confirm the soonest opening.
Serving Hillsboro, OR – Our Local Coverage Area
We serve Hillsboro and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Repair in Hillsboro
Gate repair is diagnosing and fixing what has stopped a gate working correctly, covering both the mechanical parts and the electric operator. That means hinges, posts, rollers, tracks, latches, welds and frames on the one side, and control boards, limits, loop detectors, safety reversals and drive mechanisms on the other. We specialize in the automated side as well as the mechanical, so you don’t get two contractors for one job. If you tell us the brand and the symptom when you call, we can often narrow down the likely cause before we arrive.
Most straightforward repairs finish in one visit, usually within one to three hours on site once the cause is confirmed. A weld, a track and roller service or a hinge reset is often same-day work. Jobs that need a specific operator part are scheduled around the part arriving, and we hold the price to the written estimate. The written price is agreed before we start, so you know the scope before work begins.
Most gate repairs in Hillsboro run between $150 and $800 depending on the type and extent of the failure. Driveway, sliding, metal and wood repairs tend to fall in the lower half of that range, while commercial operator work and access-control faults run higher. The estimate is free and the price is set per job by a written estimate you approve. Call (855) 251-3899 for an exact quote – estimates are free.
Yes. We service nine major gate brands, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule. We recognize the known failure points on each, which is why the diagnosis is faster and more accurate than a generalist’s guess. If your operator is one of these systems, tell us the brand when you call. Call (855) 251-3899 for an exact quote – estimates are free.
Yes, same-day repair is available on most calls when you reach us within dispatch hours. We answer the phone 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. We’re closed Saturday, and a call outside dispatch hours is booked into the next opening. Automated and operator work is measured and scheduled with a written price rather than promised same-day. Call (855) 251-3899 to check the soonest opening – estimates are free.
We stand behind the work we perform, and the written estimate spells out what the repair covers before you approve it. Because we don’t quote unverified terms, ask us at the time of estimate what applies to your specific repair and parts. You’ll get a clear answer in writing rather than a vague promise. Terms are confirmed up front and agreed before work begins.
Clear access to the gate on both sides and to the operator, and make sure the power supply and control panel are reachable. Note the brand, the exact symptoms and when the failure started, and jot down any recent changes like a power outage or a new keypad setting. Keep people and vehicles clear of a gate that’s partly open or off its track, and don’t force a stuck leaf. That information alone speeds up the diagnosis and keeps the visit efficient.
Schedule Your Gate Repair Service in Hillsboro Today
A gate that won’t cycle correctly is a daily problem that rarely fixes itself, and catching it early keeps the repair small. Call (855) 251-3899 and tell us the brand and the symptom. We answer 24/7, run fast dispatch from 7am to 7pm, Sunday through Friday, and offer same-day repair on most calls. Estimates are free and no-obligation, the price is quoted and agreed before any work starts, and gates are what we do. If you’re comparing options in terms of straight Gate Repair Hillsboro, start with the call.
Written by the team at Gate Repair Hillsboro.