Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Hillsboro?
Gate repair in Hillsboro typically costs $150 to $650 for mechanical work like hinges, rollers, latches and alignment, while automated gate repair or electric gate operator work usually runs $275 to $1,200 depending on the brand and what failed inside the control box. Simple fixes such as a sticking latch or a gate that has dropped on its hinges often land closer to $150 to $250, and a full operator board or arm replacement on a commercial-grade system can push toward the top of that range. The written estimate we give after looking at the gate is what sets your final price, and that estimate is free.
We specialize in gate systems only, so we’re not guessing at your operator. Whether your system is a LiftMaster, a FAAC, a BFT, a Linear, a Viking, a Ghost Controls, a DoorKing, an Elite or a Mighty Mule, we’ve worked on the mechanics and the electronics behind all nine brands, and that brand fluency is what keeps the diagnosis quick instead of a parts-swapping experiment.
Key Takeaways
- Mechanical gate repair in Hillsboro: typically $150 to $650.
- Electric or automated gate repair: typically $275 to $1,200.
- Full gate installation: typically $2,500 to $8,500+ depending on width, material and operator.
- Free, written estimates on every job. The estimate is the price.
- We answer 24/7 at (855) 251-3899, and we dispatch technicians 7am to 7pm, Sunday through Friday.
Gate Repair Cost Breakdown (2026)
Here’s how gate work usually prices out in the Hillsboro market this year. These are typical ranges, not a quote. The only number that matters is the one on your written estimate.
| Job Type | Typical Range | What’s Usually Involved |
|---|---|---|
| Hinge repair or replacement | $150 – $350 | Replacing worn or sagging hinges, re-aligning the gate panel, adjusting for slope |
| Latch, roller or track repair | $150 – $400 | New rollers, straightened or replaced track, latch adjustment, wheel and guide work on slide gates |
| Gate alignment or sag correction | $200 – $500 | Adjusting post-mounted hardware, correcting a gate that drags or won’t latch, checking footing |
| Electric gate operator repair | $275 – $850 | Control board, motor, limit switches, remote receiver, safety reversal diagnosis |
| Operator replacement (residential) | $700 – $1,600 | New arm or slide operator, reusing existing power and control if it’s sound |
| Loop detector or access control repair | $300 – $900 | Loop replacement, keypad, card reader, intercom wiring for commercial entries |
| Full gate installation | $2,500 – $8,500+ | New panel, posts, hardware, operator, and controls, sized to driveway and use |
What pushes a quote up? An operator from a commercial line like FAAC, BFT or DoorKing usually carries higher parts cost than a residential Mighty Mule or Ghost Controls unit, and the wiring on a slide gate with safety loops and access control is more involved than a single swing arm. What pulls it down? Catching a mechanical problem early before it grinds the operator into a bigger failure. A $200 hinge job is cheaper than a $900 operator repair every time. Wider gate panels, heavier materials and steep driveways also factor in, because the hardware has to carry more load and the operator has to move more mass.
What Affects Gate Repair Pricing in Hillsboro
- Gate type – swing or slide. A swing gate with two hinges and a simple arm operator is the most straightforward job. A slide gate adds a track, rollers, guides and often safety loops, and every one of those parts is a possible failure point that has to be tested. Slide gate repairs trend higher because there’s more system to check.
- The operator brand and control electronics. Residential-grade operators like Mighty Mule and Ghost Controls price lower on parts. Commercial-grade systems like FAAC, BFT and DoorKing carry higher-cost boards and motors, and diagnosing a control board fault takes more than a visual check. This is where specialist knowledge saves money – we test the actual fault instead of replacing parts to see what sticks.
- Age and condition of the hardware. A gate that’s been dragging on its hinges for a season wears the operator motor faster. When we look at a gate, we’re checking the mechanical side and the electrical side together, because a mechanical fault left alone will eventually take the operator with it.
- Wiring and power runs. If the gate needs new low-voltage control wiring, or a loop detector has to be cut into the driveway surface, that adds labor and material. Older installations sometimes need wiring brought up to current safety expectations, and the city’s permit rules for electrical work on a gate operator are worth confirming with the Hillsboro building department before work begins.
- Hillsboro’s wet winters and summer dry spells. Western Washington County gets a lot of rain from fall through spring, and that moisture works its way into hinge pins, roller bearings and gate hardware. Posts can shift slightly as soil moves between the wet season and the dry season, which is why gates that worked fine in August sometimes drag by February. Winter-driven moisture is also hard on control boxes and exposed wiring, so we check seals and enclosures on automated systems, not just the mechanics.
- Residential vs. commercial access needs. A homeowner’s driveway gate and a property manager’s controlled entry share the same hardware principles but not the same duty cycle. Commercial gates cycle far more often, so operator wear and access-control components (keypads, readers, intercoms) come into play. We work both, and we price each on what the gate actually does all day.
Manual vs. Electric Gate Repair: What’s the Difference in Cost?
Manual gate repairs usually fall in the $150 to $650 range, while electric gate repairs typically run $275 to $1,200. The gap comes down to what’s inside the job. A manual gate is hinges, latches, rollers, track and alignment – all mechanical, all visible, all fixable with hand tools and hardware. An automated gate adds an operator, a control board, safety reversal sensors, remote receivers and often a power run, and any one of those can be the failure.
It’s common for the two to overlap. A gate that won’t open isn’t always an operator problem. Sometimes the operator is fine and the gate is binding on a bad hinge, so the motor strains against the obstruction until it faults out or burns up. That’s why we diagnose the whole gate, not just the box with the circuit board in it. Chasing an electrical fault that turns out to be mechanical wastes your money; we’d rather find the real cause on the first visit. Gates are all we do, and the mechanical and electrical sides are handled by the same people.
If your gate is fully manual and you’re considering adding an operator, or if you’re deciding between a swing and a slide system, the pricing groundwork is the same as a new installation, and a Gate Repair Hillsboro visit is where that conversation starts.
How to Save on Gate Repair
The single biggest cost saver is speed. A gate that’s dragging or sticking is telling you something is wearing. Fix the hinge now and you avoid the operator repair later. Beyond that, a few practical habits make a real difference:
- Fix binding and dragging early. A gate that scrapes the ground or won’t latch is usually a hinge, roller or alignment issue, and those jobs sit at the low end of the price range. Left alone, the operator motor works harder every cycle and shortens its life.
- Keep the track and hinges clear. Debris in a slide gate track and grit in hinge pins accelerate wear. A quick visual check after windy stretches in Hillsboro saves hardware over the long run.
- Get a free written estimate before anyone touches the gate. The estimate is free, and the written price is what you pay. No guessing, no surprise line items. Call (855) 251-3899 and we’ll set up a visit.
- Diagnose before replacing. A gate that won’t respond isn’t always a dead operator. Remote batteries, receiver faults, limit switches and safety reversal trips are all cheaper fixes than a new motor, and brand-specific diagnosis finds them fast.
- Know your operator. When you call, tell us the brand – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite or Mighty Mule – and we’ll come prepared with the right diagnostic knowledge for that system.
Do You Charge for Estimates or Diagnostics?
No. Estimates are free, and the price is set per job by the written estimate we leave with you. We don’t tack on a separate diagnostic line for the visit. You get a clear written price for the repair, and that’s what the job costs. When you call, we’ll ask a few questions about the gate – brand, swing or slide, what it’s doing or not doing – so the technician arrives with the right focus. Call (855) 251-3899. We answer 24/7, and we dispatch 7am to 7pm, Sunday through Friday.
How Much Does Gate Installation Cost in Hillsboro?
A full gate installation in Hillsboro typically costs $2,500 to $8,500 or more, depending on the gate width, material, whether it’s swing or slide, and the operator and controls you choose. A simple residential swing gate with an arm operator sits near the lower end. A wide slide gate with a heavy panel, safety loops and access control pushes toward the top. The installation price covers the gate panel and posts, hardware, the operator, and the control wiring and setup. It’s a bigger commitment than a repair, and the right system depends on your driveway, your slope and how much use the gate will see. We handle repair, electric gate restoration and new installation under one provider, so there’s no handoff to a second contractor partway through.
What Does Electric Gate Repair Cover?
Electric gate repair covers everything between the power source and the moving panel: the operator motor, the control board, limit switches that tell the gate where to stop, safety reversal sensors, remote receivers, and the access control components on commercial entries. If your gate opens partway and stops, reverses on its own, ignores the remote, or won’t respond at all, that’s operator territory. If it opens but drags, catches or won’t latch, that’s mechanical. Most real-world failures touch both, which is why we test the whole system. A control board isn’t the problem just because the gate stopped moving – the gate might have jammed and tripped a safety feature on purpose.
Safety matters here. Gate operators carry real crushing force, and the safety reversal system is what stops a closing gate on an obstruction. If your gate’s safety reversal is behaving oddly, or the gate closes when it shouldn’t, treat it as a priority rather than something to live with. Don’t bypass a safety sensor to get the gate moving again. That sensor is there for a reason. Our technicians have up to 8 years of experience with automated systems, and we recommend a trained professional handle anything involving the operator’s wiring, power supply or control board.
For more on our core service, see gate repair.
Does the Brand of Gate Operator Affect Repair Cost?
Yes. Parts for commercial-grade operators like FAAC, BFT and DoorKing generally cost more than parts for residential-grade units like Mighty Mule and Ghost Controls, and the diagnostic time on a complex control board is higher than on a simple arm operator. That’s a real pricing factor, and it’s also why brand familiarity matters so much. We service all nine major brands – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule – so we’re not learning your system on your dime. We’ve diagnosed the fault patterns these brands are known for, which means fewer return visits and a straight answer on whether a repair is worth it.
Is It Cheaper to Repair a Gate or Replace It?
Repair is almost always cheaper when the gate panel, posts and operator frame are structurally sound – a hinge or roller job at $150 to $400 versus a full installation at $2,500 and up. Replacement starts to make sense when the panel is rusted through, the posts have shifted so badly the gate can’t be aligned, or the operator is failing repeatedly on a system that’s well past its service life. The way to know is to have someone who works on gates look at it and tell you plainly. We’ll give you the repair price and, if replacement is the better call, we’ll say so and price that too. No pressure either way. Call (855) 251-3899 for a free estimate.
What Happens When You Call
We ask about the gate – brand, type, and the symptom – so the technician arrives ready. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. If you call outside those dispatch hours, your call gets booked into the next opening. We’re closed on Saturday. When we arrive, we diagnose the gate mechanically and electrically, explain what we found, and leave you a written estimate. The price on that estimate is the price you pay, and same-day repair is often possible when the parts are on hand and the fault is clear.
FAQs – Gate Repair Cost
How much does gate repair cost in Hillsboro?
Gate repair in Hillsboro typically costs $150 to $650 for mechanical repairs and $275 to $1,200 for electric or automated gate repair, depending on the brand, the operator and what failed. The written estimate sets your final price. Call (855) 251-3899 for a free estimate.
Can you repair my specific gate brand?
Yes. We service nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule, covering both residential and commercial-grade systems. Brand-specific knowledge means faster diagnosis and no trial-and-error parts swapping. Call (855) 251-3899 to set up an estimate.
Is it cheaper to repair or replace an automated gate?
Repair is typically cheaper, often $150 to $850 compared with $2,500 or more for a full installation, as long as the gate panel, posts and frame are sound. Replacement makes more sense when the structure itself is failing or the operator keeps breaking down. Call (855) 251-3899 and we’ll price both so you can decide with real numbers.
Do you charge for a diagnostic visit or estimate?
No. Estimates are free, and the price is set per job by the written estimate we give you. There’s no separate diagnostic charge. Call (855) 251-3899 to book a visit.
Can you come today?
Same-day repair is often possible when the fault is clear and parts are on hand – mechanical fixes like hinges, latches and alignment are the most likely to be finished the same day. We dispatch 7am to 7pm, Sunday through Friday, and we’re closed Saturday. Call (855) 251-3899 and we’ll find the next opening for you.
Pricing reflects the Hillsboro market as of 2026. Gate Repair Hillsboro offers free estimates – call (855) 251-3899.
Written by the team at Gate Repair Hillsboro.
What Our Customers Say
"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Andres Morales"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Dustin Ackerman"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, swapped it, and we were moving cars again in under an hour."
- Steve Walsh