Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Motor & Opener Cost in Hillsboro?
A gate motor and opener replacement in Hillsboro typically runs $650 to $2,400 for a residential swing or slide system, including the operator, safety devices and installation labor. Swapping a single failed opener on an existing gate usually lands between $650 and $1,200. A commercial-grade operator with loop detectors and access control costs more, generally $1,800 to $4,500. The written estimate sets the final price, and every estimate we give is free. Call (855) 251-3899 to get one.
Gate Motor & Opener Cost Breakdown (2026)
Here’s how the numbers break out for the Hillsboro market in 2026. These are typical ranges for the work itself, not promotional pricing, and the written estimate you get after we look at the gate is what you actually pay.
| Item | Typical Range |
|---|---|
| Residential swing operator, single leaf | $650 – $1,400 |
| Residential slide operator | $800 – $1,800 |
| Residential opener replacement (existing gate) | $650 – $1,200 |
| Dual-leaf swing system (two operators, synchronized) | $1,400 – $2,400 |
| Commercial-grade operator (FAAC, BFT, DoorKing) | $1,800 – $4,500 |
| Control board or main circuit replacement | $250 – $650 |
| Safety photo-eye or loop detector replacement | $150 – $450 |
| Remote and receiver reprogramming or pairing | $75 – $200 |
| Battery backup install | $200 – $500 |
| Arm / gear / drive-train mechanical repair | $200 – $600 |
What pushes a gate motor job toward the high end of these ranges? A slide gate with a heavy steel frame and a long track, an operator that has to be matched to an older FAAC or BFT control board, or a commercial property that needs loop detectors wired in and the safety reversal tested before the system goes back into service. A straightforward replacement on a standard residential swing gate sits at the lower end. Gates are all we do, so we can usually tell you which end of the range you’re on from the first look at the gate and its operator. If the motor itself is fine and the problem is a control board or sensor, the number drops fast, which is why we don’t quote a full replacement until we’ve diagnosed the actual failure.
What Affects Gate Motor & Opener Pricing in Hillsboro
- Gate type and weight. A lightweight residential swing gate needs a smaller operator than a heavy commercial slide gate. Heavier barriers, longer spans and higher cycle counts all demand a bigger motor, and that shows up in the price.
- Operator brand and model. A Mighty Mule or Ghost Controls residential kit costs less than a commercial FAAC, BFT or DoorKing operator. If your gate already has a LiftMaster, Linear, Viking or Elite system, we match the replacement to what’s there instead of swapping everything out.
- Access control and safety devices. Keypads, loop detectors, photo-eye safety beams and intercoms each add cost. On a commercial property, safety reversal and detection are required for the gate to operate, so they aren’t optional line items.
- Power and wiring. If the existing circuit is adequate and the wiring is sound, installing a new operator is simple. If power has to be run out to the gate, or the wiring has seen better days, the labor climbs. Anything electrical goes to a licensed technician, not a DIY attempt.
- Condition of the gate itself. A motor bolted to a sagging gate, a worn track or a bent hinge won’t fix the problem. We sort out the mechanical side first, because a new operator on a faulty gate just wears out faster.
- The Hillsboro climate. Oregon’s wet winters and the summer dry stretch both work on an operator housing, its seals and its limit switches. Gates set in tree cover or on low ground that holds water see more corrosion and more motor strain, so we look at the housing and the gate’s footing during the estimate and price accordingly.
How to Save on Gate Motor & Opener
You don’t have to replace more than you need to. A few practical ways to keep the number down:
- Diagnose before you replace. A gate that won’t open isn’t always a dead motor. Weak batteries, a stuck limit switch or a misaligned photo-eye can mimic a failed operator. Accurate diagnosis saves the cost of a new motor you may not need, and it’s what we do on every call.
- Repair the control board when you can. A $250 to $650 board or sensor fix is far cheaper than a $1,200 replacement. Get a technician to inspect the electronics first.
- Match the brand to your gate. Don’t overspend on a commercial-grade operator for a lightweight residential gate, and don’t undersize the operator either. The wrong match costs more over the life of the system than getting it right the first time.
- Fix the little things early. A worn arm, a loose hinge or a slow slide track, caught early, extends motor life. Left alone, they wear out an operator.
- Get a free written estimate. Call (855) 251-3899 and we’ll come out and give you an exact number in writing. No guessing, no surprises.
FAQs – Gate Motor & Opener Cost
How much does gate motor and opener replacement cost in Hillsboro?
Most residential replacements in Hillsboro run $650 to $2,400, depending on gate type and operator. A single-leaf swing gate is typically $650 to $1,400. A dual-leaf or slide system lands higher. Call (855) 251-3899 for an exact quote. Estimates are free.
Is it cheaper to repair or replace a gate opener?
Repair wins when the problem is a control board, sensor, battery or mechanical part, usually $150 to $650, versus $650 to $2,400 for a full replacement. If the motor itself has failed or the operator is unsafe, replacement is the sensible option. We diagnose first, then recommend the cheaper fix if it holds. Call (855) 251-3899.
How much does a gate control board replacement cost in Hillsboro?
A control board replacement typically runs $250 to $650, depending on the operator brand. That’s far less than a new motor, and it’s the most common fix on a gate that won’t respond. We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule systems. Call (855) 251-3899.
Can you fix my gate the same day?
Yes, same-day service is available for many repairs when parts are in range and the diagnosis is clear. We answer 24/7. Call (855) 251-3899 for a free estimate. Fast dispatch from 7am to 7pm, Sunday through Friday.
Do you install or repair gate operators on commercial properties in Hillsboro?
We service commercial-grade operators including FAAC, BFT and DoorKing, along with residential systems from LiftMaster, Mighty Mule, Ghost Controls, Linear, Viking and Elite. Whether it’s a single driveway gate or a multi-leaf commercial access system, we handle the full job from diagnosis to installation. Call (855) 251-3899.
What’s the difference between a gate motor repair and a full operator replacement?
A repair handles a failed component, such as a control board, arm, sensor or battery, so the existing operator keeps running. A replacement swaps out the entire operator when the motor or control electronics are beyond repair. The price gap is significant, which is why a proper diagnosis comes first. Call (855) 251-3899 to book an on-site estimate.
If your gate needs a motor or opener and you need a clear, accurate number before you decide, call us. We’ll inspect the gate and operator at your Hillsboro property and put it in writing, with no fee and no pressure.
Call (855) 251-3899. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Estimates are free.
Pricing reflects the Hillsboro market as of 2026. Gate Repair Hillsboro offers free estimates – call (855) 251-3899.
Written by the team at Gate Repair Hillsboro.
What Our Customers Say
"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Andres Morales"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Dustin Ackerman"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, swapped it, and we were moving cars again in under an hour."
- Steve Walsh