Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Hillsboro?
Gate parts and welding in Hillsboro typically run $180 to $650 for most residential repairs, with common items like hinge replacement, roller swaps, and latch repair landing in the $180 to $340 range. Welding repairs on posts, frames, and hinges usually fall between $250 and $550 per joint, while operator-related parts like control boards and safety sensors add $220 to $900 depending on the brand. Every job is priced per the written estimate, and estimates are free.
Hillsboro sits in the Tualatin Valley, where wet winters and dry summers work on steel and galvanized hardware in a specific way. Rain gets into hinge pins and weld seams, then the dry season pulls moisture back out. That cycle loosens welds, rusts out hinges, and wears the bushings that keep a gate tracking straight. When we look at a gate here, we’re looking at what that cycle has done to the metal.
Gate Parts & Welding Cost Breakdown (2026)
Here’s what the main line items run in the Hillsboro market. These are typical estimates, not quotes. The written estimate after we see your gate sets the final price.
| Item | Typical Cost Range | What It Covers |
|---|---|---|
| Hinge replacement (per hinge) | $180 – $340 | Cutting out a worn or rusted hinge, welding in a new one, realigning the gate leaf |
| Roller and track repair | $150 – $320 | New rollers, straightened or replaced track section, gate tracking adjustment |
| Latch and striker repair | $140 – $280 | New latch hardware, striker alignment, weld if the post bracket has pulled |
| Welding – post or frame crack | $250 – $550 | Grinding out the crack, rewelding, finishing and painting the joint |
| Welding – gate frame reinforcement | $300 – $650 | Gussets or plate added to a sagging or bent frame, full seam weld |
| Drop rod repair or replacement | $150 – $300 | New drop rod, guide plate, and weld if the guide has cracked loose |
| Operator control board (brand-dependent) | $350 – $900 | Diagnosis and board replacement on LiftMaster, FAAC, BFT, Linear, Viking, DoorKing, Elite, Ghost Controls, or Mighty Mule systems |
| Safety sensors and loop detector parts | $220 – $580 | Photo-eye replacement, loop detector board, wiring at the post |
| Slide gate track and carriage repair | $280 – $600 | Ground track replacement, carriage wheel rebuild, realignment |
What pushes a job toward the high end? Heavy ornamental iron takes longer to weld and finish than a light residential aluminum gate, so the same hinge replacement costs more on iron. Rusted hardware that has seized into the post means more grinding and more time. And automated gates that also need an operator diagnosis add a separate line to the estimate.
What keeps it down? Getting the repair done before a small weld crack becomes a bent frame. A single hinge that’s caught early is a straightforward job. The same hinge left through two winters of rain usually takes the surrounding frame with it. If you’re weighing a repair against a full replacement, our gate repair Hillsboro service handles both ends, so the assessment is honest about which makes sense.
What Affects Gate Parts & Welding Pricing in Hillsboro
Six things move the number up or down more than anything else:
- Gate material. Wrought iron and heavy steel require more weld passes, more grinding, and a proper finish coat. Aluminum welds fast but needs the right filler or the joint fails again. Vinyl gates usually need hardware rather than welding, which changes the line items entirely.
- Rust and corrosion level. Hillsboro’s wet season puts real stress on galvanized hardware. A rusted hinge that still moves is a swap. One that’s fused to the post is a cut, grind, and weld. That difference is most of the price gap between the low and high end of the hinge line above.
- Gate weight and size. A 16-foot slide gate needs support and careful alignment while the frame is welded. A 4-foot walk gate can be pulled, repaired, and rehung in a fraction of the time. Larger leaves also need carriage or track work checked at the same visit.
- Automation. If your gate runs on a LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, or Mighty Mule operator, we check the mechanical repair against the operator’s alignment. A gate that’s been dragging for a season can stress the operator’s gear and control board, and the estimate will flag that before it becomes a second repair.
- Post condition and footing. A leaning post means the footing has shifted, which in the Tualatin Valley’s clay-heavy soil is common after a wet winter. Post work adds time and material. A hinge replacement on a post that’s already moving won’t hold.
- Access and site. A gate set back from the driveway with tight clearance takes longer to work around than one with open space on both sides. Commercial entries with loop detectors and access-control wiring also add diagnostic time.
How to Save on Gate Parts & Welding
The single biggest saving is catching a weld or hinge problem before it spreads. A gate that scrapes, sags, or drags is telling you something is failing. Fixing it at that stage is usually a single line item. Waiting until the frame bends or the post pulls turns it into two.
- Act on the first symptom. A gate that drags at the bottom, swings past its stop, or won’t latch clean is a mechanical problem that’s cheaper to fix now than after the frame is stressed.
- Get the operator checked at the same visit. If your automated gate has been straining, the mechanical repair and the operator diagnosis can share one on-site estimate. Diagnosing across all nine brands we service means no trial-and-error parts swapping on your dime.
- Keep the finish up. A coat of paint or rust inhibitor on weld seams and hinge pins every couple of seasons slows the corrosion cycle that drives most repairs here.
- Ask for the estimate in writing. Ours is free and sets the price per job. You’ll know the line items before any work starts.
- Don’t replace what can be repaired. A gate with good bones and a failed hinge is a repair. A gate with a bent frame and a rotted post is a conversation. We’ll tell you which one you have.
When you’re ready for a real number, call (855) 251-3899. We answer 24/7. Fast dispatch, 7am-7pm, and the estimate is free.
FAQs – Gate Parts & Welding Cost
How much does gate welding cost in Hillsboro?
Gate welding in Hillsboro typically costs $250 to $650 per repair, depending on whether it’s a crack in a post or frame, a reinforcement job, or a full hinge cut-and-weld. Heavy iron takes longer than light aluminum. Call (855) 251-3899 for an exact quote. Estimates are free.
Is it cheaper to repair or replace a gate?
Repair is almost always cheaper when the frame and posts are sound. A hinge, roller, latch, or single weld repair runs $140 to $650, while a new gate and installation costs many times that. The decision point is the frame and footing: if those are solid, repair wins. Call (855) 251-3899 and we’ll tell you honestly which side of that line your gate is on.
How much does a gate control board cost in Hillsboro?
A replacement control board typically runs $350 to $900 installed, depending on the brand. LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule boards all price differently. We diagnose across all nine brands before quoting, so you’re not paying for the wrong part. Call (855) 251-3899.
Can you come today?
Same-day service is often available in Hillsboro. We answer 24/7, and a call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Call (855) 251-3899 and we’ll get you scheduled.
Do you charge for the estimate?
No. The estimate is free, and the written estimate sets the final price per job. There’s no diagnostic fee or trip charge tacked on. Call (855) 251-3899 to book an on-site estimate.
Gates are all we do, which is why we can price a weld or a hinge accurately instead of guessing. Our technicians have up to 8 years of experience across residential driveways and commercial access-control systems, and we work with every major automated gate brand on the market.
Call (855) 251-3899 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. For more on who we are and where we work across the Tualatin Valley, see our Hillsboro page.
Pricing reflects the Hillsboro market as of 2026. Gate Repair Hillsboro offers free estimates. Call (855) 251-3899.
Written by the team at Gate Repair Hillsboro.
What Our Customers Say
"Solar panel on our remote gate wasn't keeping the battery up through the winter. He repositioned it, replaced the battery, and explained the math on why the old placement was never going to work."
- Jennifer Gallagher"Gate works properly now and the price was fair. The one thing is that it took two visits, because the operator model we have is old and the part had to be ordered. They didn't charge for the second trip."
- Scott Miller"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Andres Morales